Pryde Measurement Pty Ltd - Flow
RETURN TO HOME




Model Q5 Flow Switch

  • 5 - 85,000 GPM and Up Pipe Sizes 1" to 48" and Up.
  • Flow Detection Sensitivity 5 - 25% !!!!P <1 PSI
  • Line Pressure 300 PSIG
  • Temperature 180oF (Higher Temperer available)
  • Continuously adjustable while operating.
  • 15 amp SPDT
  • Brass body - SS hardware.

Model Q5 Data Sheet



Model Q5SS Flow Switch

  • 316 Stainless Steel Body.
  • Wetted Surfaces: 316SS, Viton and Teflon.
  • For use in chemical, petroleum, marine and severe industrial environments.
  • 1" to 48" Pipe Size, 5 - 85,000 GPM
  • Temperature 180o Pressure 300 PSIG.

Model Q5SS Data sheet



Model Q8CR Flow Switch

  • Glass reinforced inert plastic body.
  • Wetted surfaces: PPS Fortron, Viton and Hastelloy "C".
  • For use in highly particle contaminated fluids and slurries.
  • Not affected by strong acids and bases.
  • 1" - 10" Pipe Size 18 - 1900 GPM Temperature 200o Pressure 100 PSIG maximum 15 amp SPDT.

Model Q8CR Data Sheet



Model Q8N Flow Switch

  • Glass reinforced inert plastic body.
  • Wetted Surfaces: Noryl, 316SS, Hypalon Elastomer.
  • For use in highly particle-contaminated fluids and slurries, eg. sewage.
  • Not affected by mild acids and bases.
  • 1" - 10" Pipe Size 18 - 1900 GPM Temperature 200o Pressure 100 PSIG maximum.

Model Q8N Data Sheet



Model Q10N/Q10VCR

  • 0.9 GPM in 1.0" pipes to 1025 GPM in 16" pipes.
  • Factory adjustment Flow Switch Pt.
  • Temperature <1 PSI/ -40ºF to 200ºF.
  • Line Pressure to 250 PSI.
  • 5 VDC to 240 VAC/SPST Reed Switch.
  • Dry circuits to light inductive loads.
  • 316 SS/HAST. C/EPOXY.

Model Q10N/Q10VCR Data Sheet



Model Q12N/Q12CR

  • Miniature version of Model Q-10.
  • Variable Power line interface: Spade/Round Power Cord/½" Flexible conduit.
  • Cost competitive with pressure switches in O.E.M. quantities.
  • 316 SS/HAST.C/EPOXY

Model Q12N/Q12CR Data Sheet



PRECISION TURBINE FLOWMETERS

  • Flowrates from 0.25 to 12000 GPM
  • Temperature Rated to +1000oF
  • Hydraulically Balanced Rotor
  • Compact, Light-weight Construction
  • High Resolution Linear Output
  • Stainless Steel Construction
  • Standard and Custom Design
  • Variety of End Fittings Choices

Turbine Flowmeters Data Sheet





Fittings

80 Series Insertion Flow Meter

  • ½" to 12" line sizes
  • Non-drag sensing system
  • 12 VDC pulse output (up to 2,000 feet.)
  • Sapphire bearings and carbide shafts provide the bet low-flow performance of any paddlewheel type insertion meter, as well as exceptional wear resistance.
  • Material choices include PVC, polypropylene, PVDF, brass, and stainless steel.
  • Fittings, ordered separately, are individually calibrated.

80 Series Data Sheet






100/200 Series Adjustable Insertion Flow Meter

  • Adjustment means two meters handle pipe sizes from 2 to 48".
  • Flow Range: 0.3 to 30 ft./sec.
  • Signal: 12 VDC square wave
  • Cable: up to 2,000 ft.
  • Sapphire and ruby bearings for superior low-flow and long life.
  • Precisely machined parts give maximum accuracy.
  • Material choices include PVC, brass, and stainless steel.
  • These meters are ideally suited for metering pump pacing, water treatment, and flow instrumentation applications.

100/200 Series Data Sheet








WT Turbine Meters

  • In-line meters for pipe sizes 1 - ½" to 6" give highest accuracy, widest range, best particulate tolerance.
  • Turbine rotor, precisely machine from high strength plastic.
  • Sapphire bearings and carbide shafts give superb wear resistance and low friction, for very low minimum flow.
  • Turbine unit inserts through the side of the meter, any maintenance can be done without unbolting the flanges.
  • Body materials PVC, carbon steel, and stainless steel.

WT Turbine Specifications:-

Materials:-
Probe Body PVC, 304 SS, carbon steel
Rotor polypropylene, PVDF optional
Shaft Tungsten carbide, ceramic optional
Bearings Sapphire

WTC Data Sheet
WTP Data Sheet
WTS Data Sheet















S Series Low Flow Meters

  • Single-jet flowmeters for pipe sizes 3/8" to 1"
  • Flow Ranges: 0.05 to 40.0 gpm
  • Ruby and sapphire jewel bearings for very low minimum flows.
  • 12 VDC (nominal) pulse output
  • Body Polypropylene or PTFE
  • Cover: Acrylic, PVC polysulfone, polypropylene PTFE
  • Rotor: Kynar TM
  • Shafts:Tungsten carbide, ceramic opt.

S Series Data Sheet








Model 213 Piston Flow Meter
  • Flow range @ 2cP: 1 to 1800cc/min
  • Maximum operationg pressure: 70Bar or 210Bar
  • Displacement: 0.89 cc/rev
  • Weight: 0.6kg
  • Recommended filtration: 10 micron
  • Ports sizes: 1/8"NPT, #4 SAE or manifold mount
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 213 Piston Flow Meter Data Sheet




Model 213HP (High Pressure) Piston Flow Meter
  • Flow range @ 2cP: 1 to 1800cc/min
  • Maximum operationg pressure: 525Bar
  • Displacement: 1.00 cc/rev
  • Weight: 1.7kg
  • Recommended filtration: 10 micron
  • Ports sizes: #4 SAE
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 213HP Piston Flow Meter Data Sheet




Model 214 Piston Flow Meter
  • Flow range @ 3cP: 10 to 10,000 cc/min
  • Maximum operationg pressure: 70Bar or 210Bar
  • Displacement: 10.5 cc/rev
  • Weight: 3.3kg
  • Recommended filtration: 10 micron
  • Ports sizes: 3/8"NPT, #6 SAE or manifold mount
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 214 Piston Flow Meter Data Sheet




Model 214HP (High Pressure) Piston Flow Meter
  • Flow range @ 3cP: 10 to 10,000cc/min
  • Maximum operationg pressure: 525Bar
  • Displacement: 10.5 cc/rev
  • Weight: 6.5kg
  • Recommended filtration: 10 micron
  • Ports sizes: #6 SAE
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 214HP Piston Flow Meter Data Sheet




Model 215 Piston Flow Meter
  • Flow range @ 2cP: 0.07 to 35 L/Min
  • Maximum operationg pressure: 70Bar or 210Bar
  • Displacement: 47.6 cc/rev
  • Weight: 10.0kg
  • Recommended filtration: 10 micron
  • Ports sizes: 1/2"NPT or #8 SAE
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 215 Piston Flow Meter Data Sheet




Model 216 Piston Flow Meter
  • Flow range @ 2cP: 0.15 to 100 L/Min
  • Maximum operationg pressure: 70Bar or 210Bar
  • Displacement: 169.5 cc/rev
  • Weight: 25.0kg
  • Recommended filtration: 10 micron
  • Ports sizes: 3/4"NPT, #12 SAE or manifold mount
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 216 Piston Flow Meter Data Sheet




Model 234 Water Flow Meter
  • Flow range @ 1cP: 10 to 4000 cc/min
  • Maximum operationg pressure: 140Bar
  • Displacement: 10.5 cc/rev
  • Weight: 5.0kg
  • Recommended filtration: 10 micron
  • Ports sizes: 3/8"NPT
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids

Model 234 Water Flow Meter Data Sheet




Model 241 Helix Flow Meter
  • Flow range @ 3cP: 2.0 to 189 L/Min
  • Maximum operationg pressure: 35, 105 or 240Bar
  • Displacement: 0.062 L/rev
  • Weight: 13.6kg
  • Recommended filtration: 150 micron
  • Ports sizes: 1.5"NPT or 1.5"(DN40) customer supplied ANSI RF flanges
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids
  • Heat Trace: Heat traceable bodies available

Model 241 Helix Flow Meter Data Sheet




Model 242 Helix Flow Meter
  • Flow range @ 3cP: 5.0 to 540 L/Min
  • Maximum operationg pressure: 35 or 240Bar
  • Displacement: 0.182 L/rev
  • Weight: 18.1kg
  • Recommended filtration: 150 micron
  • Ports sizes: 2.5"NPT or 2.5"(DN65) customer supplied ANSI RF flanges
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids
  • Heat Trace: Heat traceable bodies available

Model 242 Helix Flow Meter Data Sheet




Model 243 Helix Flow Meter
  • Flow range @ 3cP: 15 to 1400 L/Min
  • Maximum operationg pressure: 35, or 240Bar
  • Displacement: 0.575 L/rev
  • Weight: 45.4kg
  • Recommended filtration: 150 micron
  • Ports sizes: 3"NPT or 3"(DN100) customer supplied ANSI RF flanges
  • Accuracy:
    • +/- 0.2% of reading with a linearized transmitter
    • +/- 0.5% of reading with a non-linearized transmitter
  • Fluids: most no aqueous, organic liquids
  • Heat Trace: Heat traceable bodies available

Model 243 Helix Flow Meter Data Sheet




Model G004 Gear Flow Meter
  • Flow range: 0.04 to 4 L/Min
  • Maximum operating range: 414Bar
  • Displacement: 1.8 cc/rev
  • Weight: 1.1kg
  • Recommended filtration: 15 micron
  • Port Sizes: 1/8"NPT or #4 SAE
  • Accuracy @ 30cP: +/- 0.3% of reading over a 100:1 turndown
  • Fluids: Most non-aqueous, hydrocarbon based fluids

Model G004 Gear Flow Meter Data Sheet




Model G015 Gear Flow Meter
  • Flow range: 0.15 to 15 L/Min
  • Maximum operating range: 414Bar
  • Displacement: 4.2 cc/rev
  • Weight: 1.8kg
  • Recommended filtration: 15 micron
  • Port Sizes: 3/8"NPT or #6 SAE
  • Accuracy @ 30cP: +/- 0.3% of reading over a 100:1 turndown
  • Fluids: Most non-aqueous, hydrocarbon based fluids

Model G015 Gear Flow Meter Data Sheet




Model G045 Gear Flow Meter
  • Flow range: 0.2 to 45 L/Min
  • Maximum operating range: 414Bar
  • Displacement: 13.5 cc/rev
  • Weight: 3.7kg
  • Recommended filtration: 30 micron
  • Port Sizes: 1/2"NPT or #8 SAE
  • Accuracy @ 30cP: +/- 0.3% of reading over a 100:1 turndown
  • Fluids: Most non-aqueous, hydrocarbon based fluids

Model G045 Gear Flow Meter Data Sheet




Model G105 Gear Flow Meter
  • Flow range: 1.05 to 105 L/Min
  • Maximum operating range: 414Bar
  • Displacement: 38 cc/rev
  • Weight: 7.7kg
  • Recommended filtration: 30 micron
  • Port Sizes: 3/4"NPT or #10 SAE
  • Accuracy @ 30cP: +/- 0.3% of reading over a 100:1 turndown
  • Fluids: Most non-aqueous, hydrocarbon based fluids

Model G105 Gear Flow Meter Data Sheet



P Series - Single Tube Flowmeter
  • Rib-guided or fluted metering tubes facilitate stable, accurate measurements
  • Magnifier lens in front sheild to enhance reading resolution
  • Interchangeability of flowtubes and floats
  • Ease of installation and echange of flowtubes
  • "Non-rotating" adapter feature - glass flowtubes are prevented from turning during the tightening phase of the assembly procedure
  • OPTIGRADTM scales minimise parallax and eye fatigue
  • Chemical compatibility
  • Simple means of panel mounting

P Series Data Sheet

Flow Tube Table 1 Data Sheet
Flow Tube Table 2 Data Sheet



PX Series - Multi-Tube Flowmeter
  • Rib-guided or fluted metering tubes facilitate stable, accurate measurements
  • Magnifier lens in front sheild to enhance reading resolution
  • Manifolding at inlet or outlet
  • Interchangeability of flowtubes and floats
  • Ease of installation and echange of flowtubes
  • "Non-rotating" adapter feature - glass flowtubes are prevented from turning during the tightening phase of the assembly procedure
  • OPTIGRADTM scales minimise parallax and eye fatigue
  • Chemical compatibility
  • Simple means of panel mounting

T Series Teflon® PTFE-Glass Single Tube Flowmeter
  • Constructed of inert materials; Borosilicate Glass, Teflon® (PTFE and PCTFE)
  • Chemical inert wetter parts within mechanically rigid frame
  • Rib-guided or fluted metering tubes facilitate stable, accurate measurements
  • Magnifier lens in front sheild to enhance reading resolution
  • OPTIGRADTM scales minimise parallax and eye fatigue
  • Simple means of panel mounting
  • Interchangeability of flowtubes and floats
  • Conviently overlapping flow ranges available in both standard millimeter and "direct reading" scales

TX Series Teflon® PTFE-Glass Multi-Tube Flowmeter
  • Constructed of inert materials; Borosilicate Glass, Teflon® (PTFE and PCTFE)
  • Chemical inert wetter parts within mechanically rigid frame
  • Rib-guided or fluted metering tubes facilitate stable, accurate measurements
  • Magnifier lens in front sheild to enhance reading resolution
  • OPTIGRADTM scales minimise parallax and eye fatigue
  • Simple means of panel mounting
  • Interchangeability of flowtubes and floats
  • Conviently overlapping flow ranges available in both standard millimeter and "direct reading" scales


Shown with optional tripod base
S Series Single Tub Flowmeter
  • TUBELOCKTM design simplifies installtion and replacement of tubes
  • Rib-guided or fluted metering tubes facilitate stable, accuracte readings
  • Magnifier lens in front sheild to enhance reading resolution
  • OPTIGTADTM scales minimise parallax and eye fatigue
  • Simple means of panel mounting
  • Interchangeable flowtubes and floats

G Series Gas Poportioner
  • Blending to 2 or 3 gas with gas proportioners obviates the need for
    • Ordering fixed gas mixtures
    • Contamination from reusable gas cyclinders
    • Potentially inaccurate mxtures by gas suppliers
  • Rib-guided or flured metering tubes facilitate stable, accurace readings
  • OPTIGTADTM scales minimise parallax and eye fatigue
  • Interchangeable flowtubes and floats
  • Simple means of panel mounting

Flowmeter Kits
  • Three types of kits are offered
    • Aluminium
    • Stainless steel
    • Brass
  • Kits include 4 Tubes, Floats, tools, tripod and carry case
  • Ranges from 1.8ml/min to 45227 ml/min Air
  • Ranges from 0.02 to 1288ml/min Water
  • 150mm tubes


Flowmeter Kits Data Sheet





V Series Medium Range Brass & SS Flowmeter
  • Rigid compact construction
  • Dual, rotatable direct reading scales for air or water
  • Graduations reflect both metrix and English systems
  • Vertical in-line or panel mount
  • Flow ranges from 4 to 20 L/Min Water and 140 to 900 L/Min Air

M Series Stainless Steel Industrial Flowmeter
  • Heavy duty stainless steel
  • Thick polycarbonate safety sheilds
  • Fluted or plain tapered tubes
  • Direct reading metric or English system scales
  • Unique design facilitates ease of maintenance cleaning processes
  • Ranges:
      • 9.5 to 75 L/Min Water
      • 35 to 2600 L/Min Air

xV Series Direct Reading Multi-Glass Flowmeter
  • Rigid, compact construction
  • Multi-gas, rotatable direct reading scales for 5 gases
    Argon, CO2, He, N2 & O2
  • Accuracy: +/- 5%
  • Graduations reflect both metric or English systems
  • Vertical In-line or Panel Mount

F Series In-Line Teflon® Flowmeter
  • Chemically inert wetted components
  • Removeable protective sheild
  • Individually leak tested
  • Ranges: 75 mL/Min to 45 L/Min Water

L Series Teflon® PTFE-PFA Flowmeter
  • Chemically inert wetted components constructed from PFA Teflon®,
    PTFE and PCTE
  • Non-fluid contacting structurally rigid from constructed from PFA-clad
    aluminium and Kynar
    ®
  • Overlapping flow ranges are avialable for water from 5ml/min to 45L/min
  • Individually leak tested

Optical Sensor Switch - for P, S and T Style Flowmeter
  • Mode of detection: Red LED beam break
  • Power requirements: 10 to 30VDC @ 50 mA max
  • Output transistors: NPN (1) and PNP (1)
  • NPN: Sink up to 100mA
  • PNP: Source up to 100mA
  • Response Time: 500 ms
  • Light immunity: Pulse modulared to provide extremely high immunity to ambient light
  • Ambient temperature: -30 to +70ºC operating range



Acrylic Flowmeters

FEATURES

  • Easy to read English or metric scales
  • Interchangeable scales, for routine gases
  • Customer convertible panel to partial or full in-line mounted configurations
  • Panel mounting by means of hex nuts
  • Meters are offered with or without built-in low hysteresis needle valves
  • Easy disassembly and assembly for cleaning

SPECIFICATIONS

  • Accuracy: ± 5% of full scale reading
  • Maximum temperature: 65°C
  • Maximum pressure: 6.9 bars (100 psig)
  • Meter block: Clear machined acrylic
  • Float materials: black glass, stainless steel, Carboloy® (Tungsten Carbide)
  • O-ring seals: Viton® with stainless fittings, Buna-N® with brass fittings
  • Fittings: Brass or stainless 1/8” NPT female connections, built-in needle
    valves and seal plugs

OPTIONAL PRODUCTS

  • Flow meter kits are available with direct reading scales displaying:
    Air, Water, Argon, Nitrogen, Helium, Carbon Dioxide, and Oxygen
    in both English and metric units

Polysulfone Flowmeters
  • Tough Polysulfone Meter Body Resists High Temperatures and Pressures
  • Compact Size for Tight Installation Spaces
  • Easy to Read Direct Reading Dual Scale (GPM/LPM or SCFM/M3/HR)
  • Various Scale Length Approximate
  • In-Line or Panel Mount Configurations Available.
  • Optional Integral Flow Adjustment Valve
  • Standard Models #316 Stainless Steel Guide Rods
  • (Optional Hastelloy7 C-276 Available)
  • Standard Models #316 Stainless Steel, PTFE or PVC Float
    (Optional Hastelloy7 C-276 or PVC Available)
  • Union Connections for Easy Installation and Maintenance
  • Not Recommended for Direct Sunlight Applications

AFC - Mass Flow Controller
  • Rigid metallic construction
  • 3 calibrateable flow ranges: 15, 50 & 100 L/min max
  • Maximum pressure of 500psig (34.5Bar)
  • 0-5VDC or 4-20mA signals
  • Leak intergrity 1 x 10-9 sml/sec of helium
  • Accuracy of +/-1% FS
  • Totaliser
  • Circuit Protection

AFM - Mass Flow Monitor
  • Rigid metallic construction
  • 3 calibrateable flow ranges: 15, 50 & 100 L/min max
  • Maximum pressure of 500psig (34.5Bar)
  • 0-5VDC or 4-20mA signals
  • Leak intergrity 1 x 10-9 sml/sec of helium
  • Accuracy of +/-1% FS
  • Totaliser
  • Circuit Protection

DFC - Digital Mass Flow Controller
  • Digital and analog modes operate simultaneously
  • Programmable flow configurations
  • Multi-drop capability of up to 256 units
  • 3 calibrateable flow ranges: 15, 50 & 100 L/min max
  • Stores calibration data for upt to 10 gases
  • Totaliser indicates total gas quantity
  • Alarm limits for high and low gas flow
  • Conversion factors for up to 256 gasesAuto tune function for
    optimum control responcse
  • Self diagnostic tests

DFM - Digital Multi Parameter Mass Flow Meter
  • Multi-drop capability of up to 255units (for RS485 option)
  • Stores calibrated data for 10 different gases
  • Supports 10 different engineering unit included user defined
  • Programmable 12 digits totaliser indicates total gas volume
  • Flow alarm limits for high and low gas flow with relat output
  • Pressure alarm lmits for high and low gas pressyre with relay output
  • Termperature alarm limits for high and low gas temperature with relay output
  • Four button keypad and large 128x64 graphical LCD with back light
  • Digital (RS-232 or RS-485) and aanalog outputs operate simultaneously
  • Internal conversion factors for up to 32 gases
  • Automatic zero adjustment
  • Self diagnostic tests

GFC - Low Cost Mass Flow Controller
  • Rigid metallic construction
  • Maximum pressure of 500psig (34.5 Bar)
  • Leak integrity 1 x 10-7 sml/sec of helium
  • NIST traceable certification
  • Built-in tiltable LCD readout
  • Local or remote setpoint control
  • 0-5vdc and 4-20mA signals
  • Circuit protection
  • Totaliser option

GFM - Low Cost Mass Flow Meter

  • Rigid metallic construction
  • Maximum pressure of 500psig (34.5 Bar)
  • Leak integrity 1 x 10-7 sml/sec of helium
  • NIST traceable certification
  • Built-in tiltable LCD readout
  • 0-5vdc and 4-20mA signals
  • Circuit protection
  • Can be used as a portable device
  • Engineering units or 0 to 100% displays
  • Totaliser option


XFM - Digital Mass Flow Controller
  • Supports up to 23 Engineering Units (including User Defined)
  • Stores calibration data for up to 10 gases
  • Programmable Totalizer indicates total gas quantity
  • High and low gas flow Alarm limits with preset delay interval
  • Two sets of user-programmable electromechanical SPDT relays with latch option
  • User-selectable analog 0-5 Vdc or 4-20mA outputs
  • Internal Conversion factors for up to 32 gases
  • Digital Interface (RS-232 / RS-485, Profibus DP available)
  • Multi-Drop Capability of up to 256 units (RS-485 option)
  • Optional Profibus DP interface with I&M functionality
  • Automatic sensor zero offset adjustment (via digital interface or local push button)
  • Self-Diagnostic Tests
  • Local 2 x 16 characters LCD display* with adjustable back light (optional)

XFM Digital Mass Flow Controller Data Sheet







In-Line model shown

Vortex In-Line / Insertion Flow Meter

Benefits:

  • Reliable
    • No moving part ot wear or fails
    • Electronics can be remote mounted up to 30m
    • No fluid to sensor contact
    • no holes to clog
  • Wide Rangeability
    • Hig flow turndown ration up to 80:1
    • Dual signal processing technology improves
      accuracy at low flows
  • High Accuracy
    • +/-0.5% of rate
    • increased noice cancellation as a result of dual
      signal processing technology

Functional Specifications

  • Fuild types: Steam, gas, liquid
  • Maximum pressure: 103Bar with wafer mount 
  • (see data sheet for full details)
  • Fuild temperature: -73 to 232ºC std/ to 316ºC opt
  • Low flow cut-off: Adjustable: set @ min (see data sheets)
  • High flow cut-off: Adjustable : set @ max (see data sheets)
  • Voltage: 115/230VAC selectable or 24VDC
  • Frequency: 50/60Hz
  • Outputs: Analog 4-20mA DC into 600 ohm or less
  • Linear Range: Reynolds number of >10,000



Pryde Measurement Pty. Ltd.,
ACN 112 029 777
National Customer Service - Free Call: 1800-688-211

 

Brisbane
Forest Lake, QLD 4078
Industrial: 0425 800 681
Analytical: 0425 863 095
Fax: (03) 9567 0799
P.O. Box 77
Carole Park, QLD 4300
Melbourne
Unit 2, 615 Warrigal Rd,
Ashburton, VIC 3147
Phone: (03) 9567 0777
Fax: (03) 9567 0799
Locked Bag 600,
Ashburton, VIC 3147

Perth
Hillarys, WA 6923
Industrial: 0427 517 359
Fax: (03) 9567 0799
P.O Box 221
Hillarys, WA 6923

Sydney
Unit 6, 79 Williamson Road.
Ingleburn, NSW 2565
Phone: (02) 9618 5822
Fax: (02) 9618 5844
P.O.Box 327,
Ingleburn, NSW 2565