Applications: validation of conductivity loops monitoring: - demineralisation plants in power, semiconductor, pharmaceutical and any other industries - Boiler feed water, condensates in power plants - Pharmaceutical purified water and water for injection

• Highly accurate, specifically designed for validating pure and ultrapure conductivity measurements
• Easy to connect up inlet/outlet plus electrical connections
• Specific software for calculating the cell constant
• High and low voltage versions available
• User friendly, compact and portable
• Alarm messages and 4-20mA outputs
• Certificate of conformity to ASTM and NIST

9126 Data Sheet...Click Here

An on-line analyzer for monitoring low-level sodium in ultra pure water and steam. Typical applications are in high pressure boilers such as those found in power plants etc. where the presence of NaCl in particular is known to be associated with stress corrosion cracking of boiler and superheater tubes.

• Unique standard addition automatic calibration
  
• Automatic temperature compensation
• Programmable outputs - RS232, 2x 0/4 to 20mA outputs, 2x adjustable min/max relays, alarm relay
• Optional 'K-kit' for sodium analysis in high acidity water e.g. cation exchanger samples
• Wide measurement range - 0.01 to 9999ppm

9073 Sodimat Data Sheet...Click Here

Continuous measurement of dissolved oxygen at ppb levels in ultra pure water, boiler water and condensates.

• Simple menu driven programming
• 0 to 2000ppb range with less than 1ppb detection limit
• Long-life membranes pre-mounted on retaining caps to avoid delicate membrane handling
• Two point calibration - zero and slope
• Two smart analogue outputs (measurement & temperature) with automatic recognition of the analyzer status
• Four relay outputs (high/low limits, system error and timer)

9182 Oxygen Analyser Data Sheet...Click Here

This advanced monitor is ideal for the on-line monitoring of dissolved oxygen in high purity water, boiler feedwater or condensates. It features built-in fully automatic Faraday calibration.

• 0 to 1 mg/l measuring range
• Fully automatic calibration by Faraday cell (In-situ calibration by known oxygen addition in the ppb range)
• Membranes premounted on retaining caps to avoid any delicate handling and to simplify maintenance
• High sensitivity 0.1 µg/l
• Two analogue outputs with analyser status information

9183 Oxystat Data Sheet...Click Here

Provides on-line monitoring of free chlorine in water for applications such as drinking water disinfection, reverse osmosis protection and cooling water.

• Monitoring on free chlorine and/or active chlorine (HOCl)
• Measuring range 0-5 mg/l
• Low detection limit
• pH compensation option
• No moving parts or pumps
• No reagent or conditioning agent
• Two analogue outputs with analyser status information

9184 Chloromat Data Sheet...Click Here

Provides continuous on-line monitoring of dissolved ozone in potable and pure water. Ozone is increasingly used for disinfection of drinking water, of pharmaceutical pure water loops and for mineral water bottles cleaning. The output signal of the Ozonmat should be used for automatic control of the ozonation system.

• 0 to 2 mg/l measuring range
• Very low detection limit < 5 µg/l
• No interference from other oxydising agents such as chlorine
• Automatic temperature compensation
• No moving parts
• No reagents or sample conditioning
• Two analogue outputs with analyser status information

9185 Ozonmat Data Sheet...Click Here

Continuous measurement of hydrazine in boiler water and feedwater for power plants. Hydrazine is often used as an oxygen scavenger to prevent corrosion, reduce frothing and minimize deposits on metal surfaces. Monitoring of the hydrazine level can prevent under-dosing or over-dosing with the associated costly waste. The 9186 also allows to measure other oxygen scavengers such as carbohydrazide.

• Measuring range : 0 to 500 ppb hydrazine 0 to 100 ppb carbohydrazide
• Very low drift
• Automatic temperature compensation
• No moving parts

9186 Hydrastat Data Sheet...Click Here

For continuous monitoring for trace amounts of silica in high purity water, boiler feed water, demineralization plant and semiconductor process ultrapure water.

• Continuous high stability measurement
• Automatic two-point calibration (chemical zero and slope)
• 0 to 1000ppb measuring range
• Repeatability ±0.5ppb or ±2% of the measurement
• Standard compact cabinet for wall or panel mounting
• Stable reagents need renewing only every 45 days
• Wide set of outputs: - two, programmable 'smart' analogue; three contacts for concentration and system alarms; one bi-directional RS232
• Version available for 0 to 5000ppb

9210 Silkostat Data Sheet...Click Here

For continuous monitoring of phosphates in boiler feedwater, steam generation and water supply applications.

• Discontinuous measurement , multi channel analyser
• Low Range : Molybdenum blue method range: 0-5ppm
  Repeatability +0.1 ppm or +/- 3% fo the measurement.
  or
  High Range: Vanadate method range: 0-50ppm
  Repeatability +0.5 ppm or 3% of the measurement.
• Automtic 2 point calibration
• Grab sample analysis capability
• Freely programmable sequence up to 6 streams
• Remote control of smaple sequence
• stable reagents
• Low reagent consumption : 2.5L for 45days.

Pryde Measurement Pty. Ltd.,
ACN 004 560 374
National Customer Service - Free Call: 1800-688-211