Pryde Measurement Pty Ltd - JCT Analysentechnik


		JES-301 Gas Sampling Probe Applications: For continous gas sampling in processes with dust content and humidity Removing aerosols and dust from sample Extractive gas analysis Emission monitoring and process monitoring For outdoor and indoor use Benefits: Convenient filter replacement Rapid availability Low maintenance Operation Features: Filter replacement without tools Filtration from outside to inside Calibration gas port (option) Backpurge port (option) Heated sample hose is connected directly to heated sampling probe Weather protection housing For high dust concentrations Temperature status contact Temperature controller Wide range of accessories JES-301 Data Sheet

		JES-301G Gas Sampling Probe steam heated Applications: For continous gas sampling in processes with dust content and humidity Removing aerosols and dust from sample Extractive gas analysis Emission monitoring and process monitoring For outdoor and indoor use, also in ATEX zone 1 and 2 Benefits: Convenient filter replacement No electric parts Low maintenance Operation Features: Filter replacement without tools Filtration from outside to inside Steam heated Temperature control via steam pressure Calibration gas port (option) Backpurge port (option) Heated sample hose is connected directly to steam heated sampling probe For high dust concentrations Made of stainless steel Wide range of accessories JES-301G Data Sheet

		JES-301K Back Purge Control Unit Applications: For extractive gas analysis For emission and process monitoring For control of automatic back purge of JCT gas sampling probes series JES-301 For applications with high dust concentrations For regular cleaning of probe filter, filter chamber and possible pre-filter Benefits: For in and outdoor mounting suitable Fully programmed two stage back purge program Easy adjustment of the back purge cycles by connection of only one cable Save operation due to status message No entry of purge gas into sample gas possible Features: In robust weatherproof FRP housing For wall mounting PLC (programmable logic controller) Adjustable interval for back purge cycles Status contact Safety shut off valve Control for process shut off valve JES-301K Data Sheet

		JER Sampling Pipes and JHD Pre-Filters Applications: For extractive gas analysis For emission and process monitoring For gas sampling at corrosive process gases For gas sampling at process temperatures up to 1800°C For gas sampling at high dust concentrations > 2g/m3 For adaption to all stationary JCT gas sampling probes Benefits: Easy mounting Optimal adaption of JCT gas sampling probes to the widest range of sampling conditions due to a huge variety of products Precisely definable gas sampling point due to huge variaty of sampling and extension pipes Pre-filter with V-deflector applicable also at high flow velocities in the process without damage Simple exchange Features: Wide range of different sampling pipe and pre-filter materials Wide range of different sampling pipe and pre-filter lengths All sampling pipes and pre-filters with G3/4“male thread Wide range of different extension tubes for pre-filter placement in the process Pre-filter also with V-deflector for protection against abrasion All sampling pipes and pre-filters with mounting hexagon

		JER-EH Heated Sampling Pipe Applications: For extractive gas analysis For emission and process monitoring For avoidance of acid dew point lower deviaton between sampling point and gas sampling probe Combinable with gas sampling probes JES-301 and JES-301L Benefits: Sampling without influence on the sample gas No corrosion due to condensate formation Homogeneous heating of interior and exterior pipe to 180°C due to even temperature distribution across the whole heat conductor length, independent of the operating conditions Easy mounting Pre-filter and extensions adaptable No temperature sensor necessary with HTI-16 Pt100 temperature sensor with JTC-308 Illuminated temperature display Features: Corrosion resistant double shell pipe with internal heating Heating failure monitoring with alarm contact and indication Mounting directly at the standard process flange Tube length of 500 to 2000 mm available Controlled heating up to 180°C Electronic temperature controller with temperature display Controller for wall mounting or directly mounted at the sampling tube (option) Electrical connection with plug connection STAS200 for temperature controller HTI-16 or turn-key mounted with JTC-308 JER-EH Data Sheet

		JES-301L Gas Sampling Probe Applications: For continous gas sampling in processes with dust content and humidity Removing aerosols and dust from sample Extractive gas analysis Emission monitoring and process monitoring For outdoor and indoor use Benefits: Convenient filter replacement Small outlines Quick heat up, max. 30 min. Suitable for standard applications Features: Filter replacement without tools 2 µm filter element heated to 180°C Filtration from outside to inside Calibration gas port (option) Heated sample hose connected directly to heated sampling probe Weather protection housing For dust concentrations up to 1 g/m³ Self regulating PTC heater Low temperature status contact No temperature controller needed JES-301L Data Sheet

		JES-301E1 Gas Sampling Probe Applications: For continuous gas sampling in processes with dust and humidity Ex-version Zone 1 or 2 Removing aerosols and dust from gas sample Extractive gas analysis Emission monitoring and process monitoring For outdoor and indoor use Benefits: Convenient filter replacement Rapid availability Low maintenance Operation Features: Filter replacement without tools Large filter surface Filtration from outside to inside Calibration gas port (option) Backpurge port (option) Heated sample hose is connected directly to heated sampling probe Weather protection housing For high dust concentrations Self-limited Ex-heater No temperature controller needed Wide range of accessories JES-301E1 Data Sheet

		JES-301E1SVZ Gas Sampling Probe Applications: The gas sampling probe JES 301E1SVZ is for continuous use with extractive sampling systems even where the sample contains dust and aerosols in Zone 1. The JES 301E1SVZ is available in several versions which may be custom configured to meet user's specific requirements. The JES 301Ex incorporates a non-corrosive heated, replaceable ceramic filter element with a filter porosity of 2 micron. The filter element is mounted in an electrically heated stainless steel housing, which is installed in a thermally isolated weather protection housing. The temperature regulation is done by a maintenance free, PTC heater. A cut off valve allows shutting off the gas flow on the raw-gas side. The heated line series JH can be easily connected to the JES 301Ex by a movable PG42 fastening screw. Benefits: The gas sampling probe JES 301E1SVZ is a complete unit, consisting of the heated filter head, mounting flange and probe assembly. It can be mounted anywhere horizontally or vertically. The probe can be connected with a standard 2” ANSI flange directly. The flange material is stainless steel. When mounted horizontally, the JES 301E1SVZ should be built in an angle at least between 5° and 15° from the horizontals falling, to allow condensate flow back into the process. A broad range of different materials for In-Situ probe tubes, and large In-Situ-pre filters make the JES 301E1SVZ versatile in application. Features: EX version - zone 1 Rugged construction Easy filter replacement Low maintenance Self limited Ex-heater Cut off valve on raw-gas side JES-301E1SVZ Data Sheet

		JES-301KE1 Back Purge Control Unit for Ex-Zone 1 Applications: For extractive gas analysis For emission and process monitoring in Ex-area zone 1 For control of automatic back purge of explosion proof JCT gas sample probes series JES-301 For applications with high dust concentrations For regular cleaning of probe filter, filter chamber and possible pre-filter Benefits: For in and outdoor mounting suitable For direct connection to inert gas or pressure air network No entry of purge gas into sample gas possible Protection against unauthorised access Fully programmed two stage back purge program (option PLC) Save operation due to status message (option PLC) Easy adjustment of the back purge cycles by connection of only one cable (option PLC) Features: In robust weatherproof stainless steel housing For wall mounting Lockable housing Integrated pressure regulator for inert gas or compressed air 2 explosion-proof solenoid valves (safety shut off valve and clocked back purge valvel) Manual shut off ball valve in the inlet External PLC (programmable logic controller) with adjustable interval for back purge cycles and status contact for mounting in explosion-free area as option JES-301KE1 Data Sheet

		JHPF Heated Adapter Pipe Applications: For extractive gas analysis For emission and process monitoring Process external heating of pre-filters for applications with high dust concentrations combined with high process temperatures (above maximum temperature of pre-filter) Combinable with gas sampling probes JES-351, JES-352 und JES-353 Benefits: Sampling without influence on the sample gas No corrosion due to condensate formation Uniform reliable heating of the pre-filters independant of the operating conditions Cleaning via back purge connection Easy mounting Safe operation Features: Corrosion resistant stainless steel pipe Fully electronic temperature controller with low temperature alarm and excess temperature switch-off Error message for sensor short-circuit and broken sensor Mounting directly at the standard process and gas sampling probe flange Pipe length 400 mm Temperature adjustment range 5°C....200°C Sampling pipes of arbitrary length can be screwed in on process side Back purge connection with check valve JHPF Data Sheet

		JCS-100 Sample Gas Compressor Cooler Applications: For extractive gas analysis For emission and process monitoring Continuous drying of sample gas to a precise low and constant outlet dew point Minimises water vapour cross sensitivities and volumetric errors Benefits: High flow rates and water vapour dew points possible Easy to change heat exchangers Continuous condensate removal Low maintenance operation Features: Proven and reliable technology Various heat exchanger materials One or two independent gas paths Digital temperature indication Integrated condensate pump Status contact with acoustic feedback Hot gas bypass compressor technology Temperature sensor monitoring High current volt free status relay outputs (direct pump switching) Long life fan with ball bearing Wall mount, optional free stand Fully encapsulated temperature sensor Small footprint Stainless steel housing Light weight JCS-100 Data Sheet

		JCT-1 & JCT-2 Compact and Midi Sample Gas Compressor-Coolers Applications: For extractive gas analysis For emission and process monitoring Continuous drying of sample gas to a precise low and constant outlet dew point inimises water vapour cross sensitivities and volumetric errors Benefits: Extremlely precise long term stable dew point even under varying loads High flow rates and water vapour dew points possible Easy to change heat exchangers Continuous condensate removal Low maintenance operation Easy to maintain design Features: Proven and reliable technology Performance optimised construction High performance heat exchanger Heat exchanger material PVDF, Duran glass or stainless steel One or two independant gas paths Proportional temperature controller Digital temperature indication Integrated condensate pump Status contact Compact design JCT 1 & JCT-2 Data Sheet

		JCT-3 Grand Sample Gas Compressor-Cooler Applications: For extractive gas analysis For emission and process monitoring Continuous drying of sample gas to a precise low and constant outlet dew point Minimises water vapour cross sensitivities and volumetric errors Benefits: Extremlely precise long term stable dew point even under varying loads High flow rates and water vapour dew points possible Easy to change heat exchangers Continuous condensate removal Low maintenance operation Easy to maintain design Features: Proven and reliable technology Performance optimised construction High performance heat exchanger Heat exchanger material PVDF, Duran glass oder stainless steel One to four independant gas paths Proportional temperature controller Digital temperature indication Integrated condensate pump Status contact JCT-3 Data Sheet

		JCE-2 Ex Midi Sample Gas Compressor Cooler Applications: For operation in Ex-zone 2 For extractive gas analysis For emission and process monitoring Continuous drying of sample gas to a precise low and constant outlet dew point Minimises water vapour cross sensitivities and volumetric errors Benefits: Extremlely precise long term stable dew point even under varying loads High flow rates and water vapour dew points possible Easy to change heat exchangers Continuous condensate removal Low maintenance operation Easy to maintain design Features: Proven and reliable technology with ATEX approval Performance optimised construction High performance heat exchanger with flow rates up to 350 Nl/hr Heat exchanger material PVDF or stainless steel One or two independant gas paths Proportional temperature controller Digital temperature display Integrated condensate pumps Status contact Compact design JCE-2 Data Sheet

		JCL-301 Compact Gas Conditioning System Applications: For extractive gas analysis For emission and process monitoring Continuous sample gas conditioning of humid process gases Continuous drying of sample gas to a precise low and constant outlet dew point Minimises water vapour cross sensitivities and volumetric errors Benefits: Complete solution for a great number of applications Longterm reliable reproducable measuring results Optimum operational safety due to self-monitoring Extremlely precise long term stable dew point even under varying loads Fast response time due to low dead volume Very low dissolution rates Continuous condensate removal Low maintenance operation Easy to maintain design Features: Individual configuration due to various expansion options Basic device with high-performance compressor sample gas cooler 1 or 2 independant sample gas paths Integrated condensate pumps Speed-controlled fan Connections for external sample gas pump 11 status-LED’s with event memory 2 status contacts Additional options: Easy to maintain robust fine dust filter Corrosion resistant flowmeter with precise needle valve Reliable condensate monitoring Acid dosing pump RS 485 interface JCL-301 Data Sheet

		JCL-304 / JCL-319 Gas Conditioning Systems Applications: For extractive gas analysis For emission and process monitoring Continuous sample gas conditioning of humid process gases Continuous drying of sample gas to a precise low and constant outlet dew point Minimises water vapour cross sensitivities and volumetric errors Benefits: Complete solution for a great number of applications Longterm reliable reproducable measuring results Optimum operational safety due to self-monitoring Extremlely precise long term stable dew point even under varying loads Fast response time due to low dead volume Very low dissolution rates Continuous condensate removal Low maintenance operation Easy to maintain design Features: For wall or 19"-rack mounting Individual configuration due to modular design Basic device with high-performance compressor sample gas cooler 1 to 4 independant sample gas paths Integrated condensate pumps Speed controlled fan 11 status-LED’s with event memory 2 status contacts Additional options: High performance corrosion resistant sample gas pump Easy to maintain robust fine dust filter Corrosion resistant flowmeter with precise needle valve Reliable condensate monitoring Acid dosing pump RS 485 interface JCL-304 / JCL-319 Data Sheet

		JCC-R / JCC-Q / JCC-P / JCC-L Gas Conditioning Systems Applications: For mobile or stationary extractive gas analysis For emission and process monitoring Continuous sample gas conditioning of humid process gases Continuous drying of sample gas to a precise low and constant outlet dew point Minimises water vapour cross sensitivities and volumetric errors Benefits: Complete solution for a great number of applications Sustainable reproducable measuring results Optimum operational safety due to self-monitoring Extremlely precise long term stable dew point even under varying loads Fast response time due to low dead volume Continuous condensate removal Low maintenance operation Easy to maintain design Features: 4 housing versions: 19“" mounting Rear panel mounting Side panel mounting Portable housing Individual configuration due to modular design Basic device with high-performance compressor sample gas cooler Integrated condensate pumps Digital temperature display and status-LED’s Status contact Additional options: High performance corrosion resistant sample gas pump with safety interlock Easy to maintain robust fine dust filter or disposable filter Corrosion resistant flowmeter with precise needle valve Reliable condensate monitoring JCC-R / JCC-Q / JCC-P / JCC-L Data Sheet