Calibration Requirements for Australian Food Manufacturers: What Auditors Check
If you manufacture food in Australia, calibration requirements come from several places at once: the Food Standards Code, your state food safety program, your HACCP plan, your certification scheme and, for scales, trade measurement law. Each asks for something slightly different, and audit findings tend to come from the gaps between them.
This guide maps those layers for a food or beverage plant: which instruments need calibrating, how often, what counts as proof, and what to do when a device fails. It reflects the 2026 changes to Victoria's food regulator and the release of SQF Edition 10.
What does Australian food law require you to calibrate?
The Food Standards Code sets a short legal baseline. Standard 3.2.2 requires a readily accessible thermometer that can measure potentially hazardous food to ±1°C wherever that food is handled (clause 22), and requires equipment to be kept in a good state of repair and working order (clause 21).
FSANZ guidance on thermometers adds two points that matter on a plant floor. Infrared thermometers only read surface temperature, so you still need a probe for core temperature. Gauges on equipment such as cool rooms and bain maries measure the equipment, not the food.
Clause 22 sets an accuracy, not an interval, and it says nothing about process sensors. Calibration of those instruments comes through your food safety program, your HACCP plan and your certification scheme.
That's why auditors treat calibration as part of HACCP verification. If a cook step probe reads 2°C high, the record says pass while the product may be under temperature. Calibration is what makes your monitoring records believable.
Which rules set the calibration requirements auditors check?
Most food manufacturers work under five layers at once. The table shows what each asks of your instruments and what an auditor or inspector looks for.
Requirement layer | Who sets it | What it asks of your instruments | What the auditor or inspector looks for |
Food Standards Code, Standard 3.2.2 | FSANZ, enforced by state and local government | A readily accessible thermometer accurate to ±1°C; equipment kept in good working order | A working probe, accuracy check records, damaged probes replaced |
State food safety program | State regulators, such as Safe Food Victoria or the NSW Food Authority | A documented calibration program for monitoring equipment | Equipment register, schedule, methods, records and corrective actions |
Your HACCP plan | Your HACCP team | Accurate monitoring at every critical control point (CCP), verified over time | Calibration status of each CCP instrument, traceable from the CCP record to the device |
Certification scheme (BRCGS, SQF, FSSC 22000) | Scheme owner, audited by your certification body | Risk based frequency, traceable methods, uncertainty considered at critical limits, documented action when a device fails | Equipment list with IDs and due dates, certificates, out of tolerance records |
Trade measurement | National Measurement Institute (NMI) | Scales used for trade must be an approved type, verified before use and after each repair or adjustment | A servicing licensee's verification mark; correct measurement on packaged goods |
A note for Victorian sites
Victoria changed food regulators on 1 July 2026. Safe Food Victoria replaced Dairy Food Safety Victoria, PrimeSafe and the Department of Health's food regulation functions. The underlying framework, including the Dairy Act 2000 and the Food Act 1984, didn't change at commencement, and Safe Food Victoria still publishes the dairy calibration guidance referred to throughout this article.
In NSW, the Food Authority's food safety program template includes a dedicated calibration program section, with a record sheet for thermometers and temperature gauges.
BRCGS and SQF
The BRCGS Global Standard Food Safety, Issue 9, clause 6.4, is the most detailed of the schemes. It requires sites to identify and control measuring equipment used to monitor CCPs and product safety, legality and quality. Devices must be checked at a predetermined frequency based on risk assessment, using a method traceable to a recognised national or international standard where possible.
When safety or legality relied on equipment later found to be inaccurate, the site must act so that at risk product isn't offered for sale. Issue 9 is still the audited version. BRCGS is developing Issue 10 but hasn't released it.
SQF Edition 9 requires the methods and responsibility for calibrating measuring, testing and inspection equipment to be documented and implemented. SQFI released Edition 10 in March 2026 and expects audits against it from 2 January 2027, pending GFSI benchmarking. If your procedures cross reference SQF clause numbers, check them before your next audit.
Which instruments in a food plant need calibrating?
Any instrument whose reading decides whether food is safe, legal or within specification. Victoria's dairy calibration guidance lists sensors, switches, gauges, X ray, metal detectors, scales, magnets and meters as equipment that may need calibration. On a typical food or beverage site, the register includes:
Temperature: probe thermometers, cook and chill sensors, cold room sensors, pasteuriser and retort sensors, and temperature switches on safety interlocks.
Flow: pasteuriser flow meters. The flow rate is what proves the designated holding time, and the guidance says a suitably qualified technician should calibrate it.
Pressure: steam, retort and CIP pressure, plus differential pressure across membranes and filters.
Level: pressure based level sensors in tanks of liquid product or bulk chemicals.
pH: meters calibrated against buffer solutions of known pH before use.
Humidity and water activity: drying rooms, ingredient stores and shelf stable product specifications. A water activity meter such as the Rotronic AwEasy is itself an instrument that needs regular checks.
Gas analysers: headspace analysers on modified atmosphere packaging lines. We cover why their accuracy matters in gas analysis in food packaging.
Scales and checkweighers: a quality control tool and, where product is sold by weight, a trade measuring instrument.
Inspection systems: metal detectors and X ray units, verified with test pieces during production.
A simple test for your register: if an instrument's reading appears on a CCP record, a release decision or a label, it belongs on it.
How often do food manufacturers need to calibrate?
No law sets one interval for every instrument. Frequency should be risk based: tighter for CCP instruments, harsh conditions and devices with a history of drift, and longer for stable, low risk instruments. Document the reason for each interval.
Victoria's dairy guidance shows how wide the range can be. A thermometer mounted in a refrigerated storage tank may only need calibrating annually, while a pH meter usually needs calibrating at least daily.
The NSW Food Authority recommends calibrating thermometers at least every six months depending on use, and checking cool room and freezer gauges against a calibrated thermometer at least six monthly.
Factors that should shorten an interval include:
the instrument monitors a CCP or a legal limit
it works through heat, washdown, vibration or chemical exposure
previous as found results showed drift
the manufacturer recommends a shorter interval
it was knocked, dropped or repaired, which calls for recalibration before reuse whatever the schedule says
Is calibration the same as verification?
No. Calibration compares an instrument with a traceable reference and records its error. Verification can mean a quick accuracy check, a metal detector test, or legal verification of a trade scale. Auditors expect the right one for each device.
Calibration
A comparison against a reference of known accuracy, with results recorded as found (before any adjustment) and as left (after). This is what a calibration certificate documents, and what certification schemes mean by calibration.
Routine accuracy checks
Quick in house checks between calibrations. The example record in Victoria's dairy guidance checks a thermometer monthly in ice water (−1°C to +1°C) and boiling water (99°C to 101°C).
Altitude affects the boiling point check. The NSW Food Authority notes that water boils at around 94°C in the highest NSW towns, so adjust your reference or rely on the ice point check. Routine checks catch a failed probe early, but they don't replace calibration of reference instruments.
Trade verification of scales
Scales used to sell product by weight must be an approved type, verified by a servicing licensee before use, and verified again after each repair or adjustment. The Australian trade measurement laws set these requirements, and a calibration certificate doesn't replace the verification mark.
A checkweigher that both controls pack weights and determines what you sell may need both. Scales used only for internal process control don't need trade approval, though they still need calibrating if they affect safety or quality.
Inspection system verification
Metal detectors and X ray systems are usually verified rather than calibrated. Test pieces pass through the system at regular intervals during production to confirm it detects contaminants. Record each test, the test piece sizes and what happens when a test fails.
What does traceable calibration mean in Australia?
Traceability is an unbroken chain of comparisons linking your instrument's reading back to a recognised national standard. In Australia that chain leads to the National Measurement Institute, which maintains the country's primary standards of measurement.
Many calibration guides online are written for US plants and refer to NIST. For an Australian site, ask your provider how their reference equipment traces back to national standards, and check the certificate says so.
BRCGS goes a step further for critical limits: the uncertainty of calibration must be considered when equipment is used to assess them.
Here's what that looks like. Say a cook step has a critical limit of 72°C and the probe's certificate shows an uncertainty of ±0.5°C. A reading of 72.2°C doesn't prove the product reached 72°C, because the true value could be 71.7°C. Set your operating target above the critical limit plus the uncertainty, and write that logic into your HACCP plan.
Figures are illustrative. Use your own critical limits and certificate values.
What should you do when an instrument fails calibration?
Record the as found result, identify everything measured since the last good check, and hold product whose safety or legality is in doubt. Then repair, adjust or replace the instrument and find out why it drifted.
Record the as found reading and how far outside tolerance it was.
Trace back to the last passing check and list the batches that instrument monitored since then.
Assess whether the error could have let unsafe or noncompliant product through. If so, hold it.
Adjust, repair or replace the instrument, then recalibrate and record the as left result.
Find the root cause, such as damage, drift, the wrong interval or the wrong instrument for the conditions, and update the interval or the instrument choice.
Close it out in your corrective action log, ready for the auditor.
A failed calibration becomes a serious finding when you can't show what you did about it.
What does an audit ready calibration program include?
A register, a plan and schedule, a named owner, and records you can produce on the day. These are the same building blocks set out in Victoria's dairy calibration guidance.
An equipment register
List every monitoring and measuring instrument with a unique ID, starting with those critical to food safety. Keep backup equipment, such as a spare probe thermometer or pH meter, so a failed device doesn't stop production.
A calibration plan and schedule
Document the method for each instrument, its tolerance (hot and cold points, or a weight range), the interval and the action if it fails. Include recalibration after damage or misuse.
A named owner
One person owns the program, including adding new equipment the day it's installed. That way, instruments that arrive with a line upgrade don't sit outside the program.
Records you can produce on the day
Keep records even when a contractor does the work. Link each CCP record to the ID of the instrument that produced it, so an auditor can follow the chain from product to certificate.
Should you calibrate in house or use a calibration provider?
Most sites need both. Routine accuracy checks belong in house. Reference instruments, CCP sensors, transmitters and anything that needs specialist equipment usually go to a provider, onsite or in a lab, with traceable certificates.
Victoria's guidance is practical here. Calibrate in house if you have the right equipment and people with the skills (and accreditations, where appropriate). If not, use a suitably qualified or accredited contractor or an accredited laboratory.
For installed process instruments, the choice between onsite and lab calibration usually comes down to downtime. Onsite work keeps a pasteuriser or retort sensor in place and the line running. Lab calibration suits portable instruments and anything you can swap with a calibrated spare.
How Pryde Measurement supports food and beverage calibration
Many food plants buy instruments from one supplier, calibrate them through another and repair them through a third, so nobody holds the full history of a device. Pryde Measurement supplies, calibrates and maintains the same instruments under one relationship, with a direct line back to the manufacturers that make them.
For a food or beverage site, that covers:
Calibration of pressure, flow, temperature and laboratory equipment, including electrical and mechanical calibration, onsite where pulling an instrument would stop the line
Compliance consulting, starting with an initial assessment and a gap analysis against the regulations that apply to your operation
Maintenance and repair, including routine checks, calibration verification and preventive maintenance
Instruments from long standing manufacturer partners such as Rotronic (humidity, temperature and water activity) and United Electric Controls (safety focused pressure and temperature switches)
The outcome to aim for is fewer audit findings, no product held over an out of date certificate, and lines that keep running. And if an instrument or approach isn't the right fit for your process, the team will tell you.
Want a second look at your calibration program before your next audit?
Talk to the team about your instrument register, your intervals and records, and where onsite calibration would save line time. Call 1800 688 211, email info@pryde.com.au or get in touch online.
Pryde Measurement has locations in North Melbourne VIC, Ingleburn NSW, Carole Park QLD and Kwinana WA, and supports food and beverage sites across Australia. Read more about measurement in the food and beverage industry, or why regular instrument calibration matters for uptime as well as compliance.
What else do food manufacturers ask about calibration?
Is calibration a legal requirement for food businesses in Australia?
Partly. Standard 3.2.2 of the Food Standards Code requires businesses handling potentially hazardous food to have a readily accessible thermometer accurate to ±1°C, and to keep equipment in good working order. Calibration of process instruments usually comes through your state food safety program, your HACCP plan and certification schemes such as BRCGS or SQF.
How often should a food probe thermometer be checked?
There's no single legal interval. Victoria's dairy calibration guidance uses a monthly ice water and boiling water check as its example record, and the NSW Food Authority recommends calibrating thermometers at least every six months depending on use. Recheck any probe straight away after it's dropped or damaged, and consider more frequent checks for probes used at critical control points.
Do scales and checkweighers in a food factory need NMI verification?
Scales used for trade, including weighing product that's sold or packed by weight, must be an approved type and verified by a servicing licensee before use and after each repair or adjustment. Scales used only for internal process control don't need trade approval, but still need calibrating if they affect safety or quality.
Does a metal detector need to be calibrated for a food safety audit?
Metal detectors and X ray systems are usually verified rather than calibrated. Test pieces pass through the system at set intervals during production to confirm it detects and rejects contaminants, and every result is recorded. Many sites also schedule periodic service checks based on manufacturer advice and their HACCP plan.
Does food plant calibration have to be done by an accredited laboratory?
Not always. The Food Standards Code doesn't require accredited calibration, and BRCGS asks for methods traceable to a recognised national or international standard where possible. Some customers and certification bodies do specify accredited calibration for particular instruments, so check your scheme and customer requirements before you book.
Which versions of BRCGS and SQF apply in 2026?
BRCGS Global Standard Food Safety Issue 9 is still the audited version, with Issue 10 in development. SQF Edition 10 was released in March 2026, and SQFI expects audits against it to begin from 2 January 2027, pending GFSI benchmarking. Audits before then are against Edition 9.



Comments